The Photon Replicator Kit includes a Photon Replicator Board, as well as a wearsaver and rear cover, that emulates the 15-pin D-sub electrical interface to Photon 320. A "horseshoe" shaped bracket is also included that, when attached to the Tau, exactly mimics the mounting scheme of the Photon 320 c..
Lens Focus Tool
Photon Replicator Board
Tau Locking Nut
Tau Quick Start Guide
USB Flash Drive
Latching Cable Assembly
Latching Connector, 30pin
Contact Pins (30ea)
1.5mm Hex Key
Everything You Need To Get Started
The Camera Link module is an expansion board for the Tau cameras that matches the functionality of the VPC Module and adds the ability to access digital data via Camera Link connection. The Camera Link module takes CMOS-type digital data from the Tau camera and converts it to Camera Link. This modul..
FLIR Tau PCB Wearsaver with Solder PadsA low-profile adapter that attaches to the Tau's 50-pin Hirose connector, furnishing a solder pad interface. Schematic included.The Tau2 Wearsaver was designed to be an internal engineering/manufacturing calibration accessory, rather than an OEM interface. Ther..
FLIR SDK software for the FLIR TAU Series Cameras
The Tau Software Developer's Kit (SDK part number enables camera control using one of several programming languages including VB6, VB.net, C#, and C++ (MFC). Code examples are included to help illustrate how some of the camera control functions can..
The Tau Focus Tool can be used to change the focus of the wide field of view (WFOV) 5.5mm, 7.5mm, 9mm, 13mm, or 19mm lenses.The focus-tool accessory, allows any FLIR TAU lens which cannot be focused by hand to be focused by engaging the appropriate slots on the lens barrel such that it can be rotate..
The lens locking ring is designed to mount a Tau WFOV camera into a bulkhead. The M29 x 1.0 thread on the outside of the lens mount flange is placed through the clearance hole in the bulkhead and the O-ring seals the camera to the face.
The Type 2-025 O-ring is not for sale through FLIR. This is ..
The FLIR Tau VPC Module is an interface for the camera to provide power and obtain video. It also facilitates serial communication for camera command and control via the free downloadable FLIR Camera Controller GUI. USB and Video cables are included...
Video Power Communication Interface
The Low Profile Boson VPC Interface Module simplifies integration. Two alternate Video & Power connections on the Low Profile Boson VPC Interface Module allows for a variety of installation ..
RHP-BOS-VPC-IF - USB3
Video Power Communication Interface
The Low Profile Boson VPC Interface Module simplifies integration. Two alternate Video & Power connections on the Low Profile Boson VPC Interface Module allows for a variety of ..
RHP-BOS-CL-SY-IF Camera Link Module
Converts the Boson Camera to Camera Link and provides Sync access
The RHP-BOS-CL-SY-IF Camera Link module is an expansion board for the FLIR Boson camera that can connect USB power and communication, analog video, and digital data via Camera Link..
RC-IF Remote Control Interface for the FLIR Boson
Control the Teledyne FLIR BOSON remotely with the "RC-IF" Remote Control Interface.
Two Composite Video Outputs allow connections to separate video devices, with no signal loss.
Integrating the Boson Th..
Video Power Communication (VPC) Transistor-Transistor Logic Interface Module
With the intelligent polarity sensing protection, power can be provided via the USB connection or DC Voltage using the provided 6-Pin Video/Power cable o..
Integrate the Teledyne FLIR Boson into your UAS.
The RHP-BOS-RC-HD-IF allows you to control the Boson camera remotely using a 16 Channel S-Bus Signal or up to 5 PWM Signals from your wireless Joystick Remote Control System. Now you can assign any available parameter on t..
Boson Tau Replicator Interface
The replicator board adapts the Tau 2 interfaces electronically to make them compatible to the FLIR Boson Camera. By adapting the Boson's native 80-pin Hirose connector to the 50-pin TAU 2 connector used on FLIR's Tau 2 camera accessories, i..
Boson VPC Accessory
For the FLIR Boson Thermal Imaging Cameras
The Boson video/power/control (VPC) is an accessory that adapts the native high-density electrical connector to a simpler USB-C interface. The Kit includes a VPC adapter, and a USB-C to USB-A cable...
Boson Tripod Mount
The Tripod-mount accessory, provides a means to mount a Boson assembly (or a Boson configured with either the VPC Accessory or the
Camera Link Accessory) to a tripod via a standard 1/4-20 thread. It is designed to interface to the rear of the Boson via 4 x M1.6 screws...